封面圖片

Experimental study of the laser beam cutting on acrylic sheet

In this modern era, especially in advanced of engineering materials, it was realize to develop some of non-convectional machining methods known as advanced machining process (AMPs). Laser Beam Machining (LBM) is one of the AMPs that being used nowadays for shaping almost whole range of engineering m...

Saved in:

書目詳細資料
主要作者:	Mohd Aiman, Ismail
格式:	Undergraduates Project Papers
語言:	English
出版:	2009
主題:	TJ Mechanical engineering and machinery
在線閱讀:	http://umpir.ump.edu.my/id/eprint/1045/1/Experimental%20study%20of%20the%20laser%20beam%20cutting%20on%20acrylic%20sheet.pdf http://umpir.ump.edu.my/id/eprint/1045/
標簽:	添加標簽沒有標簽, 成為第一個標記此記錄!

相似書籍

Experimental study of kerf width and taper on laser beam cutting acrylic sheet
由: Mohamad Yazid, Idris
出版: (2009)

Prediction Modelling of Surface Roughness for Laser Beam Cutting on Acrylic Sheets
由: M. M., Noor, et al.
出版: (2009)

Experimental study of the heat affected zone (HAZ) and surface roughness on laser beam cutting (LBC) on acrylic sheet
由: Faris, Suffian
出版: (2009)

A surface roughness prediction model for laser beam cutting (LBC) on acrylic sheets
由: Mohd Arif, Mokti
出版: (2008)

Response Surface Method and Neural Network to Determine Surface Roughness for Laser Cutting on Acrylic Sheets
由: M. M., Noor, et al.
出版: (2009)

Carbon Dioxide (CO2) laser cut quality of acrylic with different power levels
由: Mohd Aiman Shah, Abdullah
出版: (2008)

Optimization of laser cutting parameter of acrylic by using DMAIC approach
由: Chua, Yong Ping
出版: (2015)

Carbon Dioxide (CO2) laser cut quality of acrylic
由: Ahmad Shazwi, Kamaruzaman
出版: (2008)

Impact of Co2 laser cutting parameters on the quality of cut on PMMA sheet
由: Heng, Yee Wien
出版: (2010)

On the laser beam cutting of metallic hollow sphere structures
由: Riegel, Harald, et al.
出版: (2013)

On the numerical simulation of laser beam cutting of hollow sphere structures
由: Araújo, Manuel António, et al.
出版: (2013)

Carbon dioxide (CO2) laser cut quality of acrylic using different feed rate and constant power
由: Abd Halim, Abdullah @ Shafei
出版: (2008)

Experimental investigation on dimensional stability and cutting quality in cutting process of sugar palm fiber reinforced unsaturated polyester composites with laser beam and abrasive water jet cutting technologies
由: Masoud, Fathi, et al.
出版: (2022)

A study on laser cutting of textiles
由: Nukman, Y., et al.
出版: (2010)

Development Of Anfis Algorithm To Predict The Sheet Metal Cut Quality Of Carbon Dioxide Laser
由: Chong, Zhian Syn
出版: (2011)

Experimental evaluation of laser cut quality of glass fibre reinforced plastic composite
由: Choudhury, I.A., et al.
出版: (2013)

Experimental analysis of kerf taper angle in cutting process of sugar palm fiber reinforced unsaturated polyester composites with laser beam and abrasive water jet cutting technologies
由: Masoud, Fathi, et al.
出版: (2021)

Experimental and Numerical Investigation of CO2 Laser Cutting of Carbon/Kevlar Hybrid Composite
由: Koohi, Kaveh Moghadasi
出版: (2020)

A review of experimental and numerical analysis on laser beam machining of composites and thermoplastics
由: Kaveh, Moghadasi, et al.
出版: (2023)

Remote machining for laser cutting applications
由: Raja Mohd Salleh, Raja Bahtiar
出版: (2008)

The study on the effect of laser power on kerf width for carbon dioxide laser cutting process
由: Ahmad Shahrul Amrie, Mohd Supri
出版: (2012)

Laser Welding of Thin Sheet Magnesium Alloys
由: M., Ishak, et al.
出版: (2012)

Quality and Performance Analysis of CO2 Laser machining - A Complete Guide For Laser Machining Experimentation and Cut Edge Quality Evaluation
由: Sivarao, Subramonian
出版: (2010)

Experimental and numerical investigation on multi-pass laser cutting of natural fiber composite
由: Khairul Fikri, Tamrin, et al.
出版: (2020)

Optimization of carbon dioxide laser cutting parameters
由: Muhammad Iqbal, Mohd Azit
出版: (2012)

Influence of laser cutting parameters on the cutting quality of inconel 718
由: Mohd Halim, Nurhaliana Shazwani
出版: (2022)

Study the energy recovery in acrylic boiler /
由: Ummu Atirah , Hanipah
出版: (2012)

Experimental study of formability of sheet metal in deep drawing process
由: Muhammad Safwan, Ismail
出版: (2011)

Characterization of laser beam intensity used for machining
由: Mohd Syimir Haziq, Noor Zainal
出版: (2009)

Transforming Linear Laser Cutting machine Into Laser Lathing – An Empirical Investigation & Evaluation of Roundness Quality
由: Sivarao, Subramonian, et al.
出版: (2012)

Application of focused ion beam for machining of nanopillar sheet
由: Ali, Mohammad Yeakub
出版: (2011)

Effect of laser micro-drilling parameters on hole geometry and hole formation of thin sheet SS304
由: Haneef, M. S., et al.
出版: (2023)

Development of Statistical Model to Predict Ra and Rz in the Laser Cutting
由: M. M., Noor, et al.
出版: (2009)

Effect of Pressure, Frequency and Duty Cycle on Laser Cut Surface
由: Samsudin, Abdul Rahim, et al.
出版: (2008)

Multiple-objective optimization in precision laser cutting of different thermoplastics
由: Tamrin, K. F., et al.
出版: (2015)

Measurement of Liquid Sheet using Laser Tagging Method by Photochromic Dye
由: Nurrina, Rosli, et al.
出版: (2014)

Experimental Investigation and Parameter Optimization of Low Power CO2 Laser Cutting of a Carbon/Kevlar Fibre-reinforced Hybrid Composite
由: Khairul Fikri, Tamrin, et al.
出版: (2019)

Development of laser cutting and engraving machine utilising PC-NC controller
由: Nik Mohamed, Nik Mohd Zuki, et al.
出版: (2008)

Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates
由: Abd Halim, Nor Farah Huda, et al.
出版: (2011)

A review on laser beam welding of copper alloys
由: Auwal, S.T., et al.
出版: (2018)