Fabrication Of Cold Spray Ti-O Coatings Engineered From Agglomerated Powders
Current attention has focused on the preparation of thick ceramic coating using nanostructured materials as feedstock materials using thermal spray process. Cold spray method has appeared as a promising process to form ceramic nanostructured coating without significantly changing the microstructure...
Saved in:
Main Author: | |
---|---|
Format: | Thesis |
Language: | English |
Published: |
UTeM
2016
|
Subjects: | |
Online Access: | http://eprints.utem.edu.my/id/eprint/18875/1/Fabrication%20Of%20Cold%20Spray%20Ti-O%20Coatings%20Engineered%20From%20Agglomerated%20Powders%2024%20Pages.pdf http://eprints.utem.edu.my/id/eprint/18875/ http://library.utem.edu.my:8000/elmu/index.jsp?module=webopac-d&action=fullDisplayRetriever.jsp&szMaterialNo=0000102260 |
Tags: |
Add Tag
No Tags, Be the first to tag this record!
|
Summary: | Current attention has focused on the preparation of thick ceramic coating using nanostructured materials as feedstock materials using thermal spray process. Cold spray method has appeared as a promising process to form ceramic nanostructured coating without significantly changing the microstructure of the initial feedstock materials whereas many conventional thermal spray processes do due to its low processing temperature. However, deposition of ceramic powders by cold spray is not easy due to brittle characteristics of the material. Moreover, the bonding mechanism on how the ceramic coating was formed on the substrate is still unclear as this method requires plastic deformation of particles upon the impact onto the substrate.
Therefore, in this study, focused have been made on the TiO2 nanostructured feedstock materials which were synthesized throughout of the study. The properties of the powders also have been altered by several conditions in order to make it suitable for cold spray deposition. The mechanism of coating deposition and properties of the feedstock powders were investigated in this study. The following results which obtained by this study were summarized as below:
1. In this work, the synthesis of agglomerated TiO2 powders, which are ready to be used as feedstock materials for a cold spray process after synthesis via a simple hydrolysis (TiO2-H) and hydrothermal (TiO2-HT) process, is described. The XRD patterns showed that single phase anatase TiO2 was able to be produced using a low temperature process for the hydrolysis and hydrothermal methods. However, the results showed that TiO2-H powders have a smaller crystallite size and broader peaks compared with TiO2-HT powders. SEM and TEM analysis confirmed that the TiO2-H powders were built up from nano-sized particles, and were further agglomerated into micrometer-size, which is a preferable size for the cold spray process. On the other hand, TiO2-HT powders showed a formation of agglomerated particles with minimal particle agglomeration which was revealed by the SEM image and the particle size analyzer. A preliminary study on coating deposition using cold spray showed that TiO2-H powders can be deposited onto ceramic tile substrate with a ~50μm thickness. Meanwhile for TiO2-HT powders, only particle embedment can be observed on the surface of the substrate. The results reveal that porosity contained in the agglomerated morphology is important in order to build up the coating by cold spray due to the tendency of the porous structure to break easily upon impact onto the substrate.
2. To further clarify the effect of porosity contain in the powder for the cold spray deposition, effect of low calcination on the as-synthesized TiO2 by hydrolysis method have been conducted. Then, as-synthesized TiO2 and calcined TiO2 powders were studied on coating deposition by cold spray process. The results of this study indicated that a post treatment on TiO2 powder improved powder deposition on ceramic tile substrate via the cold spray method. The cross-section of the obtained coating which was observed using SEM showed that nanoparticles TiO2 powders in the agglomerated form were able to be deposited on the substrate and formed a thick coating. A stacking of agglomerated TiO2 powders was found on the cross-section observation which is due to the breaking up of ceramic particles which was induced by porosity in the powder and is believed to be responsible for the formation of the coating. The results of this study also reveal that, when the feedstock powders have denser packing of particles and minimum number of porosity in the powder, breaking of particles during the spraying become more difficult. This hard and dense particle made them resistant to fragmentation and adherence on surface of the substrate.
3. Further study have been conducted by addition of ammonium sulfate; (NH4)2SO4 during the powder synthesis. Addition of structure-directing agent, (NH4)2SO4 promotes the agglomeration to occur with denser closed packing of particle arrangement which reduce the number of existing porosity in the synthesized powder. The addition of (NH4)2SO4 addition was found to be very effective to unite the nano-sized particles together to form agglomeration in order to form the tertiary particles. The preliminary study of coating formation depicted that the powder obtained could be used as the feedstock powder for cold spray process to make coating as it can be deposited onto the ceramic tile substrate. Once again, porosity in the powders was deduced as one of the crucial factors that contribute to better deposition of TiO2 coating by cold spray process. Plastic deformation also may contribute to the formation of coating due to the used of nanostructured powders which received high local compact pressure during the spraying process.
4. Further studies on the obtained coating have been investigated. The study reveals that the properties of the coating (hardness, roughness and porosity) also depend on the properties of the initial feedstock powders. Moreover, anatase phase was preserved as revealed by the XRD analysis. This finding proves that cold spray process is suitable process to fabricate TiO2 coating which can prevent phase transformation to occur due to low processing temperature. Details observation on the surface and cross-section of the coatings show that nanostructured particles from the feedstock powders were well-retained in the coating structure.
5. In order to study the individual particle impact morphologies, wipe tests were conducted on aluminum, copper and ceramic tile substrate. From the SEM observation, the results showed that the collided particles were plastically deformed and adhered on the hard ceramic tile substrate during deposition. However, in the case of aluminum and copper substrate, the splat diameters were smaller than the feedstock powder size and both particles and substrates were deformed during the collision. Moreover, many craters were observed on these metal substrates. It was found that the deposition behavior of TiO2 particle and the crater formation by the cold spray process was affected by the hardness and surface roughness of the substrate materials.
|
---|