Relationship of surface roughness with current and voltage during wire EDM
Wire EDM is in use for a long time for cutting punches and dies, shaped pockets and other machine parts. Surface finish of the machined surface mainly depends on current and voltage used during machining. In the present research experimental investigations have been conducted to establish relation...
Saved in:
Main Authors: | , , |
---|---|
Format: | Article |
Language: | English |
Published: |
Asian Network for Scientific Information
2006
|
Subjects: | |
Online Access: | http://irep.iium.edu.my/7863/1/2317-2320.pdf http://irep.iium.edu.my/7863/ http://scialert.net/abstract/?doi=jas.2006.2317.2320 |
Tags: |
Add Tag
No Tags, Be the first to tag this record!
|
id |
my.iium.irep.7863 |
---|---|
record_format |
dspace |
spelling |
my.iium.irep.78632014-11-26T01:33:10Z http://irep.iium.edu.my/7863/ Relationship of surface roughness with current and voltage during wire EDM Khan, Ahsan Ali Mohd Ali , Munira Shaffiar, Norhashimah TS200 Metal manufactures. Metalworking Wire EDM is in use for a long time for cutting punches and dies, shaped pockets and other machine parts. Surface finish of the machined surface mainly depends on current and voltage used during machining. In the present research experimental investigations have been conducted to establish relationships of job surface finish with current and voltage. Brass wires of diameters 0.3, 0.25, 0.20 and 0.15 mm were used. Work materials tested were mild steel, aluminum, cemented carbide, copper and stainless steel. After machining each material with specific current and voltage the hardness and the job surface roughness were measured and their surfaces were obsetved under an electron-scanning microscope. Results of the experiments show that in general the machined surface becomes rougher with increase in current and voltage. Microstructures of the specimens also show that craters on the finished surface become larger as a result of using higher current and voltage. It was also found that wires of smaller diameters give smoother surface than those cut with larger diameters. It has been established that machining of carbides should be limited to wires with diameter equal to or less than 0.15 mm. Use of wires of greater diameters causes frequent wire breakage. A statistical analysis was done to pick up the most probabilistic data from the bank of data obtained from the experiments. Finally, mathematical relationships have been developed between job surface finish with current and voltage within the specified ranges for a few work materials. Asian Network for Scientific Information 2006 Article REM application/pdf en http://irep.iium.edu.my/7863/1/2317-2320.pdf Khan, Ahsan Ali and Mohd Ali , Munira and Shaffiar, Norhashimah (2006) Relationship of surface roughness with current and voltage during wire EDM. Journal of Applied Sciences, 6 (10). pp. 2317-2320. ISSN 1812-5662 (O), 1812-5654 (P) http://scialert.net/abstract/?doi=jas.2006.2317.2320 10.3923/jas.2006.2317.2320 |
institution |
Universiti Islam Antarabangsa Malaysia |
building |
IIUM Library |
collection |
Institutional Repository |
continent |
Asia |
country |
Malaysia |
content_provider |
International Islamic University Malaysia |
content_source |
IIUM Repository (IREP) |
url_provider |
http://irep.iium.edu.my/ |
language |
English |
topic |
TS200 Metal manufactures. Metalworking |
spellingShingle |
TS200 Metal manufactures. Metalworking Khan, Ahsan Ali Mohd Ali , Munira Shaffiar, Norhashimah Relationship of surface roughness with current and voltage during wire EDM |
description |
Wire EDM is in use for a long time for cutting punches and dies, shaped pockets and other machine
parts. Surface finish of the machined surface mainly depends on current and voltage used during machining.
In the present research experimental investigations have been conducted to establish relationships of job
surface finish with current and voltage. Brass wires of diameters 0.3, 0.25, 0.20 and 0.15 mm were used. Work
materials tested were mild steel, aluminum, cemented carbide, copper and stainless steel. After machining each
material with specific current and voltage the hardness and the job surface roughness were measured and their
surfaces were obsetved under an electron-scanning microscope. Results of the experiments show that in general
the machined surface becomes rougher with increase in current and voltage. Microstructures of the specimens
also show that craters on the finished surface become larger as a result of using higher current and voltage. It
was also found that wires of smaller diameters give smoother surface than those cut with larger diameters. It
has been established that machining of carbides should be limited to wires with diameter equal to or less than
0.15 mm. Use of wires of greater diameters causes frequent wire breakage. A statistical analysis was done to
pick up the most probabilistic data from the bank of data obtained from the experiments. Finally, mathematical
relationships have been developed between job surface finish with current and voltage within the specified
ranges for a few work materials. |
format |
Article |
author |
Khan, Ahsan Ali Mohd Ali , Munira Shaffiar, Norhashimah |
author_facet |
Khan, Ahsan Ali Mohd Ali , Munira Shaffiar, Norhashimah |
author_sort |
Khan, Ahsan Ali |
title |
Relationship of surface roughness with current and voltage during wire EDM |
title_short |
Relationship of surface roughness with current and voltage during wire EDM |
title_full |
Relationship of surface roughness with current and voltage during wire EDM |
title_fullStr |
Relationship of surface roughness with current and voltage during wire EDM |
title_full_unstemmed |
Relationship of surface roughness with current and voltage during wire EDM |
title_sort |
relationship of surface roughness with current and voltage during wire edm |
publisher |
Asian Network for Scientific Information |
publishDate |
2006 |
url |
http://irep.iium.edu.my/7863/1/2317-2320.pdf http://irep.iium.edu.my/7863/ http://scialert.net/abstract/?doi=jas.2006.2317.2320 |
_version_ |
1643606025171894272 |
score |
13.18916 |