Influence of process parameters on surface integrity during EDM of mild steel
The present paper reports on the influence of process parameters on surface quality of mild steel during EDM using a copper electrode. Surface quality was evaluated on the basis of work surface roughness, micro cracks and thickness of the recast layer. Current, pulse-on time, pulse-off time and volt...
Saved in:
Main Authors: | , , |
---|---|
Format: | Conference or Workshop Item |
Language: | English |
Published: |
2010
|
Subjects: | |
Online Access: | http://irep.iium.edu.my/3274/1/Full_Paper.pdf http://irep.iium.edu.my/3274/ |
Tags: |
Add Tag
No Tags, Be the first to tag this record!
|
id |
my.iium.irep.3274 |
---|---|
record_format |
dspace |
spelling |
my.iium.irep.32742017-06-20T03:44:01Z http://irep.iium.edu.my/3274/ Influence of process parameters on surface integrity during EDM of mild steel Khan, Ahsan Ali Adesta, Erry Yulian Triblas Mohammad , Yeakub Ali TS200 Metal manufactures. Metalworking The present paper reports on the influence of process parameters on surface quality of mild steel during EDM using a copper electrode. Surface quality was evaluated on the basis of work surface roughness, micro cracks and thickness of the recast layer. Current, pulse-on time, pulse-off time and voltage were the variable parameters for the present investigation. It was found that pulse-on time is the most significant factor for work surface roughness. With increase in pulse-on time the work material gets more time to absorb heat and more melting and vaporization of material takes place producing a rough surface. Work surface roughness was also found to increase with increase in current. A higher current produces a spark of higher energy removing more material and leaving a larger crater that results a rough surface. An increase in voltage also results a poorer surface, but voltage demonstrated to have a very small effect on job surface roughness. Micro cracks were found on the surface due to rapid heating and cooling of the surface during EDM. Micro cracks reduced in number and size when the surface was EDMed with a low current and a short pulse-on time. A layer of recast layer on the work surface was observed after EDM. The thickness of the recast layer was higher while a higher current together with a higher pulse-on time were used. It was concluded that in order to have a high quality surface it should be machined with lower values of current, pulse-on time and voltage. 2010 Conference or Workshop Item REM application/pdf en http://irep.iium.edu.my/3274/1/Full_Paper.pdf Khan, Ahsan Ali and Adesta, Erry Yulian Triblas and Mohammad , Yeakub Ali (2010) Influence of process parameters on surface integrity during EDM of mild steel. In: 22nd United Kingdom-Malaysia Engineering Conference 2010, 8-9th April, 2010, London. |
institution |
Universiti Islam Antarabangsa Malaysia |
building |
IIUM Library |
collection |
Institutional Repository |
continent |
Asia |
country |
Malaysia |
content_provider |
International Islamic University Malaysia |
content_source |
IIUM Repository (IREP) |
url_provider |
http://irep.iium.edu.my/ |
language |
English |
topic |
TS200 Metal manufactures. Metalworking |
spellingShingle |
TS200 Metal manufactures. Metalworking Khan, Ahsan Ali Adesta, Erry Yulian Triblas Mohammad , Yeakub Ali Influence of process parameters on surface integrity during EDM of mild steel |
description |
The present paper reports on the influence of process parameters on surface quality of mild steel during EDM using a copper electrode. Surface quality was evaluated on the basis of work surface roughness, micro cracks and thickness of the recast layer. Current, pulse-on time, pulse-off time and voltage were the variable parameters for the present investigation. It was found that pulse-on time is the most significant factor for work surface roughness. With increase in pulse-on time the work material gets more time to absorb heat and more melting and vaporization of material takes place producing a rough surface. Work surface roughness was also found to increase with increase in current. A higher current produces a spark of higher energy removing more material and leaving a larger crater that results a rough surface. An increase in voltage also results a poorer surface, but voltage demonstrated to have a very small effect on job surface roughness. Micro cracks were found on the surface due to rapid heating and cooling of the surface during EDM. Micro cracks reduced in number and size when the surface was EDMed with a low current and a short pulse-on time. A layer of recast layer on the work surface was observed after EDM. The thickness of the recast layer was higher while a higher current together with a higher pulse-on time were used. It was concluded that in order to have a high quality surface it should be machined with lower values of current, pulse-on time and voltage. |
format |
Conference or Workshop Item |
author |
Khan, Ahsan Ali Adesta, Erry Yulian Triblas Mohammad , Yeakub Ali |
author_facet |
Khan, Ahsan Ali Adesta, Erry Yulian Triblas Mohammad , Yeakub Ali |
author_sort |
Khan, Ahsan Ali |
title |
Influence of process parameters on surface integrity during EDM of mild steel |
title_short |
Influence of process parameters on surface integrity during EDM of mild steel |
title_full |
Influence of process parameters on surface integrity during EDM of mild steel |
title_fullStr |
Influence of process parameters on surface integrity during EDM of mild steel |
title_full_unstemmed |
Influence of process parameters on surface integrity during EDM of mild steel |
title_sort |
influence of process parameters on surface integrity during edm of mild steel |
publishDate |
2010 |
url |
http://irep.iium.edu.my/3274/1/Full_Paper.pdf http://irep.iium.edu.my/3274/ |
_version_ |
1643605111172235264 |
score |
13.18916 |